Korvi lisatud toodetele saab ka paari klikiga küsida nimelise ja ametliku hinnapakkumise, soovi korral koos paigaldusega.
Eesti piires on kohaletoimetamine tasuta
Tegu on kompaktse kuid väga jõulise line-array võimendussüsteemi komponendiga Itaalia kvaliteetootjalt RCF. Seadme maksimaalne helirõhk on 133 dB ning võimsus 700W RMS.
HDL-10A koosneb kahest 8″ madal- ja kesksageduselemendist ning ühest 2,5″ kõrgsageduselemendist.
Antud line-array moodulitega saab luua vähe ruumi võtvaid, kuid väga hea katvusega ning detailse ja puhta heliga võimendussüsteeme. Samuti on võimalus komplekteerida valget värvi helivõimendussüsteeme, et nad sulanduksid paremini saaliga.
Nii kõlarielemendid kui ka kastid on disainitud selliselt, et neid saaab ka välioludes vihmaga kasutada kattes vaid tagaosas ühenduskohad ja nupud spetsiaalsete vihmakatetega.
Terve Eesti piires on kohaletoomine tasuta.
Allpool olev info on pärit tootja kodulehelt:
Tehniline infoleht: en_HDL10-A-spec-sheet
Kasutusjuhend: Manual-HDL-20-A HDL-10-A
Võimalikud süsteemikonfiguratsioonid:
kompaktne HDL10-A micro system config
väiksem HDL10-A small system config
keskmine HDL10-A medium system config
suur HDL10-A large system config
The HDL 10-A is a two way active line array module designed for live sound reinforcement and installed sound applications. It features: 2 x 8-inch woofers, 1 x 2.5-inch titanium compression driver, digital amplifier with switch mode power supply and DSP controlled Input section with selectable presets. The HDL 10-A delivers: 133dB max SPL; 1400 Watt peak power (700 Watts RMS); 65Hz – 20kHz frequency response.
The HDL 10-A is a true active and high power ready to use touring system equipped with a high efficiency digital amplifier that delivers superior SPL reducing energy requirement. The integrated processing and the cabling reduction will make the set-up faster and easier and, thanks to its compact size, the truck space requirement is reduced to the minimum.
The integrated processing and the cabling reduction will make the set-up faster and easier.
The compactness and lightweight of the system combined with top of class steel on board mechanics helps during rigging operations as well as during transportation.
The HDL 10-A is powered by a 1400W peak power digital amplifier, split 200W for the HF and 500W for the LF. A new generation DSP handles all the processing within the cabinet and allows adjustment of Cluster size and HF projection. The DSP also includes presets for indoor/outdoor usage and highly curved arrays. All these setting are accessed by the buttons on the rear of the cabinets.
The easy to access controls on the back of the speaker allow a number of simple optimisations to be carried out at the flick of a switch: two possible HF settings, four possible cluster configurations; a special EQ setting for high curved configurations and an Indoor Correction EQ.
MAIN XLR INPUT (BAL/UNBAL). The system accept female XLR input connectors and line level signals from a mixing console or other signal source.
LINK XLR OUTPUT. The output XLR male connector provides a loop trough for speakers daisy chaining.
Controls the volume of the power amplifier. The control ranges from – (maximum attenuation) to the MAX level (maximum output).
POWER INDICATOR. Power on indicator. When the power cord is connected and the power switch is turned on this indicator lights green.
SIGNAL INDICATOR. The signal indicator lights green if there is signal present on the main XLR input.
LIMITER INDICATOR. The amplifier has a built in limiter circuit to prevent clipping of the amplifiers or overdriving the transducers. When the peak clipping circuit is active the LED blinks orange. It is okay if the limit LED blinks occasionally. If the LED blinks frequently or lights continuously, turn down the signal level. The amplifier has a built in RMS limiter. If the RMS limiter is active the LED lights red. The RMS limiter has the purpose to prevent damages the transducers. The speaker shall never be used with the limit indicator red, continuous operation with the RMS protection active can cause damages to the speaker.
HF. The switch gives the possibility to set high frequencies correction depending on target distance (air absorption correction):
– NEAR (used for pole mount applications or near field)
– FAR (for farthest field).
The combination of the 2 switches gives 4 possibilities of mid low frequencies correction depending on cluster size.
– 2-3 modules (used for pole mount applications ground stacking)
– 4-6 modules (small flown systems)
– 7-9 modules (medium flown systems)
– 10-16 modules (maximum flown configuration).
The switch gives the extra possibility to boost mid frequencies depending on a high curving cluster configuration of few pieces.
– OFF (not active correction)
– ON (for high curving arrays of few pieces HDL10A).
The switch gives the extra possibility to set low frequencies correction depending on a indoor/outdoor use, in order to compensate room reverberation on lows.
– OFF (not active correction)
– ON (correction for reverberant indoor rooms).
AC POWERCON RECEPTACLE.
RCF D LINE uses a POWERCON locking 3-pole AC mains. Always use the specific power cord provided in the package.
AC POWERCON LINK RECEPTACLE.
Use this receptacle to link one or more units. Always make sure that the maximum current requirement does not exceed the maximum admitted POWERCON current. In case of doubt call the closest RCF SERVICE CENTRE.
POWER MAIN SWITCH.
The power switch turns the AC power ON and OFF. Make sure that the VOLUME is set to – when you turn on the speaker.
In order to assist with the set up procedures for the HDL 10-A line array system, RCF has developed a complete prediction software package.
The software enables a complete two dimensional simulation of the behaviour of the HDL 10-A modules and also suggest the correct subwoofer combination.
The system curvature angles and the sound projection data are computed with maximum sound pressure levels for the given design.
The software will allow simulations up to a maximum of sixteen HDL 10-A systems.
The rigging menu provides data for weight, centre of gravity and length of the array configuration. Rigging points and rigging hardware configurations are also computed.
…
– 2.0″ Inside-Outside voice coil
– Water resistant fibre doped cone
– Polycotton M-roll surround
– High power magnetic structure
Edge wound voice coils – ensuring the best linear frequency response and maximum SPL output
The ND640 large format compression driver delivers one of the key advantages of the HDL 10-A, the 2.5” voice coil allows a crossover point of 800Hz and therefore almost all of the vocal range can be produced by this driver. This allows better coverage and dispersion control, and superior efficiency.
RCF has developed an oxygen free process of moulding pure titanium ultra thin films in high quality, finely controlled shaped diaphragms. Our process offers superior sonic quality, extended to the highest audible frequencies which guarantee consistent power handling and reliability.
RCF has developed a unique voice coil, combining the advantages of inside/outside technology to the superior quality of polyimide-imide materials (wire resins and former resins). The inside/outside coil offers many advantages: – the dissipation surface is doubled – the adhesion area to the former is doubled – during thermal expansion the former is squeezed between inside and outside layers offering the best mechanical resistance.
The custom designed waveguide allows a precise coverage of 100 x 15 degrees, whilst also delivering a superb,linear high frequency response.
Thanks to the large format compression driver on a wave-guide, the HDL 10-A offers superior intelligibility over distance
The RCF HDL will maintain its intelligibility, definition and signal strength while competitors’ models will attenuate and break up before the sound reaches its throw distance.
The HDL 10-A tour grade system comes in a structurally wooden reinforced composite polypropylene enclosure, and is equipped with two aluminium side handles with rubber handgrips and two rear pocket handles for portability.
The integrated mechanics are both fast and reconfigurable, allowing the system engineer to create genuine J-shaped or spiral arrays.
The top model shows a typical RCF line array hang with the angles set and splayed in 2-degree resolution. On the other hand, competitors’ models are already pre-configured with constant curvature fixed angles, with no opportunity to optimise the system to the venue’s characteristics.
In this class, the competitors’ pre-configured line arrays referred to will typically be restricted to four or five elements, whereas the RCF solution can handle up to 16 modules, variably configurable, to produce a genuine J-shaped array.
Thanks to its large format compression driver on a waveguide, the HDL 10-A offers superior intelligibility over distance.
Due to its symmetrical design the HDL-10A produces constant coverage without break up or attenuation.
The custom designed waveguide allows a precise coverage of 100 x 15 degrees, whilst also delivering a superb, linear high frequency response.
The HDL 10-A cabinet features two newly designed die-cast aluminium side handles powder coated and with rubber hand-grip.
The heavy duty front grille is power coated. A special transparent-to-sound foam backing on the inside of the grille helps to further protect the transducers from dust.
